Paper preparation guidelines

Described below are the particular requirements for submission of papers to DIPAC 2007 - the general requirements are explained in the text of the templates available from JACoW.

All contributions should be uploaded via the Internet using the facilities provided by the organizers. However, authors must also submit a hard copy at the conference and are reminded that, since no contributions are accepted for publication only, any paper accepted for presentation, which is not presented by one of the authors at the conference, will be excluded from the proceedings. Furthermore, the Programme Committee reserves the right to refuse papers for publication which have not been properly presented in the poster sessions. Manuscripts of contributions to the proceedings (or enlargements of them) are not considered as posters and papers presented in this way will not be accepted for publication.

Manuscripts

Authors are advised to use the templates and in case of difficulties they should consult the JACOW electronic publication help pages. The templates contain styles which, when applied, will automatically ensure correct typesetting and layout.

Length of Contributions

Contributed papers for both oral and poster presentation may be up to 3 pages long and only invited papers may be up to 5 pages.

General Layout

See the template for a typical implementation of the requirements. Manuscripts should be prepared for one side of the paper and

Either A4 (21.0 cm x 29.7 cm; 8.27 in x 11.69 in) or US letter size (21.6 cm x 27.9 cm; 8.5in x 11.0 in)
Single spaced text in two columns of 82.5 mm (3.25 in.) with 5. 3mm (0.2 in.) separation.
The text located within the margins specified as follows to facilitate electronic processing of the postscript file.

The margins should be as follows:

Margins	A4 paper	US Letter paper
Left	20 mm	20 mm
Right	20 mm	26 mm
Top	37 mm	19 mm
Bottom	19 mm	19 mm

Authors should use only TIMES or Times New Roman (in roman, bold or italic) and Symbol fonts. All contributions should use 10pt fonts for the normal text. Title

The title should use 14pt bold uppercase letters and be centred on the page. The names of the authors and their organisation/affiliation and mailing address should be listed alphabetically in 10pt upper and lower case letters, grouped by affiliation. When there is more than one author, the submitting author's name should be given first, followed by the other names in alphabetical order.

Section Headings

Section headings should use 12pt bold uppercase letters and be centred in the column. They should NOT be numbered.
Widow and Orphan Control: All headings should appear next to the following text - there should never be a column break between a heading and the following paragraph.

Subsection Headings

Subsection headings should use 12 pt italic letters, be left aligned and justified in the column. As for section headings, they should NOT be numbered.

Figures and Tables

Place figures and tables as close to the place of their mention as possible. Lettering in figures and tables should be large enough to reproduce clearly, using only the approved fonts. Use of non-approved fonts in figures often leads to problems when the files are processed and may even cause loss of information. All figures and tables must be given sequential numbers (1, 2, 3, etc.) and have a caption placed below the figure or above the table being described. If a displayed equation needs a number, place it flush with the right margin of the column.

References

All bibliographical references should be numbered and listed at the end of the paper in a section called "REFERENCES". When referring to a reference in the text, place the corresponding reference number in square brackets. See the sample paper for a typical example.

Acronyms

Acronyms should be defined the first time they appear.

Page Numbers

DO NOT have page numbers. They will be added by the Editing Team when they produce the final proceedings.

Templates

Authors are strongly advised to use the template corresponding to the correct version of WORD and not to transport the document across different platforms e.g. MAC <-> PC or across different versions of WORD on the same platform.

Paper preparation checklist

Use only TIMES or Times New Roman (roman, bold or italic) and Symbol fonts (in the text and in the figures), 10 pt minimum.
Check that the postscript file prints correctly.
Check that there are no page numbers.
Check that there are no section or sub-section numbers.
Check that the margins are correct on the printed version (left 20mm (0.79in), bottom 19mm (0.75in), overall height of text 241mm (9.5in)). There may be differences of ą1 mm on the margins from one printer to another.
Check the size of the file - an average size should be <3 MBytes. PostScript files which are larger than 5 MBytes often cause problems and will almost certainly require modification. If the PostScript file for the paper falls into this category, please consult the JACoW recommendations for diagnosis and remedies for large files .

Paper submission instructions